Tag Archives: Door

What is a Window Door Retrofit Technician?

Posted on by

The pressing issues on environmental concerns often find its roots in the wrong decisions and lifestyles of people especially on their unconscious preference of throwing out or getting rid of certain materials in their immediate households. The green movement in its objective to save the earth from further destruction endorses the concept of reuse, reduce and recycle. Thus, a great alternative that would definitely boost this particular concept is the green job that most homeowners fail to recognize, the profession for window or door retrofit technician.

Window or door retrofit technicians are professionals who specialize in window or door component replacement in order to avoid eventual disposal of the whole thing. Some of the basic components that are replaced are the frame, glass and sash using new materials like double-paned glasses with low-E value, new sash and vinyl frame.

This method of window or door upgrade proved to be a very cost-efficient and practical way of preserving and retaining windows especially good lumber that it is made of. Thus, the concept is quite clear, the work of window or door retrofit technicians contribute to the preservation of trees and prevents more logging activities because the manufacture of windows would be lessened after all.

What are the work and importance of this profession?

Aside from the known contribution of window or door retrofit technicians in the advocacy of green movement, other benefits could be experienced by those who hire certified professionals in this milieu. Basically, those who purchase windows or doors and want to upgrade them for enhancement or fixture would need professional help in the installation and replacement of materials needed for the task.

– Window and door retrofit technicians have sufficient knowledge and training especially in citing necessary and required adjustments to be done on the window or door.

– Furthermore, they are skilled professionals who know how to properly replace woods and other components which may likely be due to termite-caused rottenness and defects.

– Qualified professionals or technicians know the proper and correct way of installing items which would eventually prevent instances of damage or something that would repeat the work over again. What are the certifications and trainings required?

Since window and door retrofit technicians are now in-demand amidst the prevalent economic and environmental crisis, more trainings and stringent standards are imposed to add to the eligibility of professionals who would join in this particular milieu. Here are some of the trainings and qualifications needed to be a certified window or door retrofit technician.

– Field Experience through regulated training and development. Make sure that the course you take is standardized AWDI accredited with qualified references, sufficient input and practical courses.

– Skill improvement seminars and courses are needed for remarkable customer service credited to a good product background and installation improvement.

– Installation instructions with standardized data are necessary for effective installation despite the variation in different manufacturer’s products and items.

Window and door technician therefore plays a salient role as a vital component that is not only necessary in the real estate industry but most of all as important contributors to the preservation of the environment particularly the trees.

Dismantling Tips For Prewar Cars – The Doors

Posted on by

For the novice, tackling a door repair for the first time can be a frustrating and time consuming experience. While the majority of prewar automobiles have common dismantling techniques, learning these techniques can be a challenge. These techniques are not often described in manuals and period maintenance references. This is simply because it was considered common knowledge.

Tackling the repair of doors need not be frustrating. Most of it requires a bit of knowledge about what to look for and what bolt to turn. Here are some of the more common tips and techniques useful for dismantling the prewar car door for repairs.

The exterior door handle, especially the driver’s side, is one of the most used parts of the automotive body. While they seldom break, it can be necessary to remove them for other repairs or servicing. Door handles are generally held in place by one of two methods.

In the case of the door handle where a small plate with two bolts around the base of the handle can be seen on the outside of the door, the removal seems straight forward. Remove the two screws or bolts and pull. This may result in a spike in blood pressure. The handle should also be held in place by a third bolt accessible only by removing the interior door panel. This third bolt is located in the end of the handle shaft and prevents the removal of the handle by vandals or pranksters and unscrupulous antique auto restorers.

The second method of removal involves handles with no obvious exterior bolts. Handles of this type require the loosening of a setscrew in the edge of the door. The small set screw will be visible through a hole in the door edge. The hole may be covered by a small cap. Loosen the set screw and the door handle can be removed for repair or replacement. When reinstalling be sure to turn the set screw tight and ensure that it is at least flush with the edge of the door.

Stiff lock action could be a sign that the lock mechanism is about to seize. A squirt or two of powdered graphite from a spray dispenser could save you from dismantling the unit. If the problem persists it may require removing the offending mechanism from the door.

Some automobiles will have a lock unit separate from the handle. This type of lock unit is held in place by a set screw. Open the door and look at the door’s jam at the level of the lock . A small set screw will be visible through a hole. The hole may be covered by a small cap. Turning the set screw counterclockwise the screw will loosen and the lock barrel can be removed for repair or replacement. When reinstalling be sure to turn the setscrew tight and at least flush with the edge of the door jam.

In the case where the lock is located in the handle, the entire handle must be removed as describe above. Then the lock and handle can be sent away for repair, or replaced.

Removal of interior handles is accomplished by removing either a retaining pin or clip. These are accessed by depressing the escutcheon plate or ring to expose the pin or clip. The pin is usually easily pushed through using a suitably stiff wire or small punch. With the clip or pin removed the handle slips off the shaft.

Upholstery panels are best removed with either a specialty tool or a wide putty knife. The blade of the tool is slid up against the spring clips or nails and the panel pried away from the door. Prying as close as possible to the clips or nails lessens the possibility of tearing the panel or fabric. It is also wise to inspect the panel before dismantling to ensure you have removed any extra screws or other fasteners which may have been installed over the lifetime of the vehicle.

With the interior panel removed window and latch mechanisms can be accessed. While the door latch mechanism is a straight forward matter of removing the mounting bolts or screws, the window mechanism requires additional work.

Removal of the window mechanism can be accomplished without removing the glass, but the glass should be removed first. This is often accomplished by lowering the window, removing all window trim and possibly a section of window channel. This allows room to raise the glass up and out of the door. With the glass removed, the bolts retaining the mechanism can be removed for servicing.

When tackling any repair where manuals may not be available, it is wise to make notes as you go. You may think you can remember how it goes together, but a note, small drawing or photos of the dismantling process may assist in jogging your memory. The notes and images will also come in handy the next time you have to tackle a door repair.

Components of Frameless Shower Doors

Posted on by

When building your own frameless shower door, there are crucial parts and components to consider. These parts and components are called hardware. Like any hardware, they are necessary to build and construct a planned project. Certain materials and tools are also required to successfully build it.

Major Components

The major hardware categories required for frameless shower doors are door hinge, glass clamps and brackets, pulls and handles, wipes and seals, u-channels or thresholds, towel bars, and other designer accessories. You can usually find these components in your nearest hardware stores as they are not that hard to find.

Door Hinge

Before buying certain components, you need to make sure that you plan out of what specific door you want to construct. If you settle for a swinging type of shower door, a shower door hinge is needed. Basically, like other hinges, they are used to hold 2 parts together so that one can swing relative to the other.

Glass Clamps

For some who chose glass shower doors, glass clamps are necessary in order to hold the glass together. At the same time, brackets is needed to hold glasses too especially if your shower door enclosures are built in the corner.

Pull or Handle

Another very important hardware is the pull or handle. Whether you have a sliding, bi-fold, or swinging door, one needs a handle or pull to access the shower door. One can choose from a variety of style, design, and finishes to suit one’s need of convenience and elegance.

Wipes and Seals

Another equally important part of shower enclosure doors are wipes and seals. Aside from sealing every glass or any material used for the shower door, they serve as a stopper for water or air from going outside the shower enclosure so one can avoid any water overflow in the bathroom.

U-Channels or Thresholds

Next are u-channels or thresholds. These components are good for securing the bottom and the top of shower enclosures for secure and safe usage. Remember, different u-channels and thresholds are available depending onto what type of door you use. So always pick the one that is appropriate for your door or else you will not be able to put together the materials.

Towel Bars and Accessories

The last but certainly not the least are the towel bars and other designer accessories. Using such will add convenience for one’s daily shower use and other important necessities like shower trays, hand holders and what not. Adding a certain personal design can also personalize your bathroom interior.

Always choose what is suitable for your needs and don’t over accessorize. Always make it simple when choosing the right door components to fit your everyday lifestyle.